Saw English www.tool-tool.com @ BW Professional Cutter Expert www.tool-tool.com

Bewise Inc. www.tool-tool.com Reference source from the internet.

Saw
A crosscut saw about 620 mm long
Classification	Cutting
Types	Hand saw Back saw Bow saw Circular saw Reciprocating saw Band saw
Related	Milling cutter

This article is about the tool, for the films series see Saw (film series)

A saw is a tool that uses a hard blade or wire with an abrasive edge to cut through softer materials. The cutting edge of a saw is either a serrated blade or an abrasive. A saw may be worked by hand, or powered by steam, water, electric or other power.

In a modern serrated saw, each tooth is bent to a precise angle called its "set". The set of the teeth is determined by the kind of cut the saw is intended to make. For example a "rip saw" has a tooth set that is similar to the angle used on a chisel. The idea is to have the teeth rip or tear the material apart. Some teeth are usually splayed slightly to each side the blade, so that the cut width (kerf) is wider than the blade itself and the blade does not bind in the cut.

An abrasive saw uses an abrasive disc or band for cutting, rather than a serrated blade.

According to Chinese tradition, the saw was invented by Lu Ban. In Greek mythology, Perdix, the nephew of Daedalos, invented the saw. Historically, however, saws date back to prehistory, and likely evolved from Neolithic tools or bone tools.

[edit] Saw terminology

Diagram showing the teeth of a saw blade when looking front-on. The teeth protrude to the left and right, so that the saw cut (kerf) is wider than the blade width. The term set describes how much the teeth protrude.

Heel: The end closest to the handle.
Toe: The end farthest from the handle.
Front: The side with the teeth (the "bottom edge").
Back: Opposite the front ("top edge").
Teeth: Small sharp points along the cutting side of the saw.
Gullet: Valley between the points of the teeth
Fleam: The angle of the faces of the teeth relative to a line perpendicular to the face of the saw.
Rake: The angle of the front face of the tooth relative to a line perpendicular to the length of the saw. Teeth designed to cut with the grain (ripping) are generally steeper than teeth designed to cut across the grain (crosscutting)
Points per inch (25 mm): The most common measurement of the frequency of teeth on a saw blade. This is measured by setting the tip, or point, of one tooth at the zero point on a ruler, and then counting how many points are contained within one inch (25 mm) of length, counting inclusively. There will always be one more point per inch than there are teeth per inch (e.g., a saw with 14 points per inch will have 13 teeth per inch, a saw with 10 points per inch will have 9 teeth per inch). Some saws do not have the same number of teeth per inch throughout their entire length, but the vast majority do.
Teeth Per inch : Another common measurement of the amount of teeth residing in any one inch length of a saw blade. Usually abbreviated as TPI, eg a blade consisting of 18TPI (Teeth Per Inch).
Kerf: Width of the saw cut. On most saws the kerf is wider than the saw blade because the teeth are flared out sideways (set). This allows the blade to move through the cut easily without getting stuck (binding). However, some saws are made so that the teeth have no set on one side. This is done so that the saw can lie flat on a surface and cut along the surface without scratching it. These are referred to as flush cutting saws. The term kerf is often used to mean the width of the saw blade. However it is the width of the cut so it is the width of the blade plus any wobble created during cutting plus any material pulled out of the sides of the cut. This distinction can be extremely important. If you try to use a blade that is too thin you can get excessive wobble and actually get a wider kerf.

[edit] Types of saw blades and the cuts they make

Blade teeth are of two general types: Tool steel or carbide. Carbide is harder and holds a sharp edge much longer.

Crosscut: In woodworking, a cut made at (or near) a right angle to the direction of the grain of the workpiece. A crosscut saw is used to make this type of cut.
Rip cut: In woodworking, a cut made parallel to the direction of the grain of the workpiece. A rip saw is used to make this type of cut.
Plytooth: A circular saw blade with many small teeth designed for cutting plywood with minimal splintering.
Dado blade: A special type of circular saw blade used for making wide grooved cuts in wood so the edge of another piece of wood will fit into the groove to make a joint. Dado blades can make different width grooves by addition or removal of chipper blades of various widths between the outer dado blades. This first type is called a stacked dado blade. There is another type of dado blade capable of cutting variable width grooves. An adjustable dado utilizes a moveable locking cam mechanism which causes the blade to wobble sideways more or less. This allows continuously variable groove width from the lower to upper design limits of the dado.

[edit] Materials used for saws

There are several materials used in saws, with each of its own specifications.

Brass: Mostly used in back saws because of its low price, its flow characteristics that make the material relatively easy to cast, and unlike other types of saw, the forces that take place in back saws are relatively low because of the pulling motion used.
Steel: Used in almost every existing kind of saw. Because steel is cheap, easy to shape, and very strong, it has the right properties for most kind of saws.
Diamond: Used only in saws for the really heavy cutting. It is very expensive and comes in two shapes: ropes and circular saws. Mostly used for cutting concrete and other materials with rock-like structures or in softer materials, such as wood, where the precision and high volume of work justifies the expense of diamond-edged cutting tools. Diamond saws are made by combining powder metal with diamond crystals, which are then heated and pressed into a molding to form the diamond segments.

[edit] History

[edit] Handmade manufacture

Saws until at least the mid-19th century were made laborously by hand. Teeth were punched out individually, then "set" by striking alternate teeth with a hammer against a "stake" or small anvil. Due to risk of breaking teeth, beginners were given saw-set pliers which set even more slowly.^[1]

[edit] Pit Saw

In early English North America the pit saw was one of the principal industrial tools that made the mercantilist system successful. It was (generally) operated over a pit across which the logs to be cut into boards were mounted. The saw was "a strong steel cutting-plate, of great breadth, with large teeth, highly polished and thoroughly wrought, some eight or ten feet in length" (Upham Hist. of Salem v1, p 191) with a handle on either end. The pit saw took at least 2 men to operate. One stood in the pit - the pitman, who was responsible for raising the saw on the backstroke - and the other was above - the sawyer, responsible for guiding the cut. The workers at a pit saw were some of the best paid in early colonial North America.

The pit saw is also known as a whipsaw.^[2]

[edit] Uses

Saws are most commonly used for cutting hard materials. They are used extensively in forestry, construction, demolition, medicine, and hunting.
Some saws are used to make music.
Chainsaw carving is a flourishing modern art form. Special saws have been developed for this purpose.
Some musicians use saws to produce unique sounds.

歡迎來到Bewise Inc.的世界，首先恭喜您來到這接受新的資訊讓產業更有競爭力，我們是提供專業刀具製造商，應對客戶高品質的刀具需求，我們可以協助客戶滿足您對產業的不同要求，我們有能力達到非常卓越的客戶需求品質，這是現有相關技術無法比擬的，我們成功的滿足了各行各業的要求，包括：精密HSS DIN切削刀具、協助客戶設計刀具流程、DIN or JIS 鎢鋼切削刀具設計、NAS986 NAS965 NAS897 NAS937orNAS907 航太切削刀具,NAS航太刀具設計、超高硬度的切削刀具、BW捨棄式鑽石V卡刀’BW捨棄式金屬圓鋸片、木工捨棄式金屬圓鋸片、PCD木工圓鋸片、醫療配件刀具設計、汽車業刀具設計、電子產業鑽石刀具、全鎢鋼V卡刀-電路版專用’全鎢鋼鋸片、焊刃式側銑刀、焊刃式千鳥側銑刀、焊刃式T型銑刀、焊刃式千鳥T型銑刀、焊刃式螺旋機械鉸刀、全鎢鋼斜邊刀電路版專用、鎢鋼焊刃式高速鉸刀、超微粒鎢鋼機械鉸刀、超微粒鎢鋼定點鑽、焊刃式帶柄角度銑刀、焊刃式螺旋立銑刀、焊刃式帶柄倒角銑刀、焊刃式角度銑刀、焊刃式筒型平面銑刀、木工產業鑽石刀具等等。我們的產品涵蓋了從民生刀具到工業級的刀具設計；從微細刀具到大型刀具；從小型生產到大型量產；全自動整合；我們的技術可提供您連續生產的效能，我們整體的服務及卓越的技術，恭迎您親自體驗！！

BW Bewise Inc. Willy Chen willy@tool-tool.com bw@tool-tool.com www.tool-tool.com skype:willy_chen_bw mobile:0937-618-190 Head &Administration Office No.13,Shiang Shang 2nd St., West Chiu Taichung,Taiwan 40356 http://www.tool-tool..com / FAX:+886 4 2471 4839 N.Branch 5F,No.460,Fu Shin North Rd.,Taipei,Taiwan S.Branch No.24,Sec.1,Chia Pu East Rd.,Taipao City,Chiayi Hsien,Taiwan