Bewise Inc. www.tool-tool.com Reference source from the internet.
A reamer or ream is a tool used in machining to enlarge holes. Reamers are used mostly in the metalworking areas of machining. They may be used as hand tools or in the spindles of machine tools such as milling machines or drill presses.
[edit] Overview of design and function
[edit] Reamer body
A typical reamer consists of a set of parallel straight or helical cutting edges along the length of a cylindrical body. Each cutting edge is ground at a slight angle and with a slight undercut below the cutting edge. Reamers must combine both hardness in the cutting edges, for long life, and toughness, so that the tool does not fail under the normal forces of use. They should only be used to remove small amounts of material. This ensures a long life for the reamer and a superior finish to the hole.
The spiral may be clockwise or counter-clockwise depending on usage. For example, a tapered hand reamer with a clockwise spiral will tend to self feed as it is used, possibly leading to a wedging action and consequent breakage. A counter-clockwise spiral is therefore preferred even though the reamer is still turned in the clockwise direction.
[edit] Shank types (drive types)
For production machine tools, the shank type is usually one of the following: a standard taper (such as Morse or Brown & Sharpe), a straight round shank to be held by a collet, or a straight round shank with a flat for a set-screw, to be held by a solid toolholder. For hand tools, the shank end is usually a square drive, intended for use with the same type of wrench used to turn a tap for the cutting of screw threads.
[edit] Why ream? Why not just drill to size?
The geometry of a hole drilled in metal by a twist drill may not be accurate enough (close enough to a theoretically true cylinder of a certain precise diameter) and may not have the requisitely smooth surface finish for certain engineering applications. Although modern twist drills can perform excellently in many cases—usually producing sufficiently accurate holes for most applications—sometimes the stringency of the requirements for the hole's geometry and finish necessitate two operations: a drilling to slightly undersize, followed by reaming with a reamer. The planned difference between the drill diameter and the reamer diameter is called an allowance. (It allows for the removal of a certain small amount of material.) Drilling followed by reaming generally produces hole geometry and finish that is as close to theoretical perfection as possible. (The other methods of hole creation that approach nearest to perfection under certain conditions are boring [especially single-point boring] and internal cylindrical grinding.)
[edit] Types of reamers
[edit] Adjustable hand reamer
An adjustable hand reamer can cover a small range of sizes. They are generally referenced by a letter which equates to a size range. The disposable blades slide along a tapered groove. The act of respectively tightening and loosening the restraining nuts at each end varies the size that may be cut. The absence of any spiral in the flutes restricts them to light usage (minimal material removal per setting) as they have a tendency to chatter. They are also restricted to usage in unbroken holes. If a hole has an axial split along it, such as a split bush or a clamping hole, each straight tooth will in turn drop into the gap causing the other teeth to retract from their cutting position. This also gives rise to chatter marks and defeats the purpose of using the reamer to size a hole.
[edit] Straight reamer (precision)
A straight reamer is used to make only a minor enlargement to a hole. The entry end of the reamer will have a slight taper, the length of which will depend on its type. This produces a self centering action as it enters the raw hole. The larger proportion of the length will be of a constant diameter.
Reamed holes are used to create holes of precise circularity and size, for example with tolerances of -0/+0.02mm(0.0008") This will allow the force fitting of locating dowel pins, which need not be otherwise retained in the body holding them. Other holes, reamed slightly larger in other parts, will fit these pins accurately, but not so tightly as to make disassembly difficult. This type of alignment is common in the joining of split crankcase halves such as are used in motorcycle motors and boxer type engines. After joining the halves, the assembled case may then be line bored (using what is in effect a large diameter reamer), and then disassembled for placement of bearings and other parts. The use of reamed dowel holes is typical in any machine design, where any two locating parts have to be located and mated accurately to one another - typically as indicated above, to within 0.02mm or less than 0.001".
Another use of reamed holes is to receive a specialized bolt that has an unthreaded shoulder - also called a sholder bolt. This type of bolt is commonly used to replace hot peened rivets during the seismic retrofit of structures.
[edit] Hand reamer
A hand reamer has a longer taper or lead in at the front than a machine reamer. This is to compensate for the difficulty of starting a hole by hand power alone. It also allows the reamer to start straight and reduce the risk of breakage. The flutes may be straight or spiral.
[edit] Machine reamer
A machine reamer only has a very slight lead in. Because the reamer and work piece are pre-aligned by the machine there is no risk of it wandering off course. In addition the constant cutting force that can be applied by the machine ensures that it starts cutting immediately. Spiral flutes are essential on a machine reamer to clear the swarf automatically.
[edit] Rose reamer
A rose reamer has no relief on the periphery and is offset by a back taper to prevent binding. They are primarily used as roughing reamers.
[edit] Shell reamer
Shell reamers are designed for reaming bearing and other similar items. They are fluted almost their whole length.
[edit] Tapered reamer (precision)
A precision tapered reamer is used to make a tapered hole to later receive a tapered pin. A taper pin is a self tightening device due to the slow angle of the taper. They may be driven into the tapered hole such that removal can only be done with a hammer and punch. They are sized by a number sequence (for example, a No.4 reamer would use No.4 taper pins). Such precision joins are used in aircraft assembly and are frequently used to join the two or more wing sections used in a sailplane. These may be re-reamed one or more times during the aircraft's useful life, with an appropriately oversized pin replacing the previous pin.
[edit] Morse taper reamer
A morse taper reamer is used manually to finish morse taper sleeves. These sleeves are a tool used to hold machine cutting tools or holders in the spindles of machines such as a drill or milling machine. The reamer shown is a finishing reamer. A roughing reamer would have serrations along the flutes to break up the thicker chips produced by the heavier cutting action used for it.
[edit] Combination Reamer
A combination reamer has two or more cutting surfaces. The combination reamer is precision ground into a pattern that resembles the part’s multiple internal diameters. The advantage of using a combination reamer is to reduce the number of turret operations, while more precisely holding depths, internal diameters and concentricity. Combination reamers are mostly used in screw machines or second-operation lathes and not with Computer Numerical Control ( CNC ) machines because G-Code can be easily generated to profile internal diameters.
Combination reamers can be made out of cobalt, carbide, or high-speed tooling. When using combination reamers to ream large internal diameters made out of material with lower SFM , carbide tips can be brazed onto a configured drill blank to build the reamer. Carbide requires additional care because it is very brittle and will chip if chatter occurs. It is common to use a drill or combination drill to remove the bulk of material to reduce wear, or the risk of the part pulling off on the combination reamer.
[edit] Tapered reamer (non-precision)
A tapered reamer may be used cleaning burrs from a drilled hole, or to enlarge a hole. The body of the tool tapers to a point. This type of reamer consists of a body which, typically, is up to 1/2 inch in diameter, with a rod cross piece at the large end acting to form a handle. It is especially useful for working softer metals such as aluminum, copper, and mild steel. A similar tool can be seen on select Swiss Army knives, such as the Electrician model, to be used on conduit.
[edit] Additional uses and types
Often, hobby grade radio control cars need reamers to have the holes drilled for the mounting of the bodies. Although similar to metal reamers, radio control body reamers are small, and the tip is usually conic, with flue areas on each side to help create the holes.
歡迎來到Bewise Inc.的世界，首先恭喜您來到這接受新的資訊讓產業更有競爭力，我們是提供專業刀具製造商，應對客戶高品質的刀具需求，我們可以協助客戶滿足您對產業的不同要求，我們有能力達到非常卓越的客戶需求品質，這是現有相關技術無法比擬的，我們成功的滿足了各行各業的要求，包括：精密HSS DIN切削刀具、協助客戶設計刀具流程、DIN or JIS 鎢鋼切削刀具設計、NAS986 NAS965 NAS897 NAS937orNAS907 航太切削刀具,NAS航 太刀具設計、超高硬度的切削刀具、醫療配件刀具設計、汽車業刀具設計、電子產業鑽石刀具、木工產業鑽石刀具等等。我們的產品涵蓋了從民生刀具到工業級的刀 具設計；從微細刀具到大型刀具；從小型生產到大型量產；全自動整合；我們的技術可提供您連續生產的效能，我們整體的服務及卓越的技術，恭迎您親自體驗！！
BW Bewise Inc. Willy Chen willy@tool-tool.com bw@tool-tool.com www.tool-tool.com skype:willy_chen_bw mobile:0937-618-190 Head &Administration Office No.13,Shiang Shang 2nd St., West Chiu Taichung,Taiwan 40356 TEL:+886 4 24710048 / FAX:+886 4 2471 4839 N.Branch
Welcome to BW tool world! We are an experienced tool maker specialized in cutting tools. We focus on what you need and endeavor to research the best cutter to satisfy users’ demand. Our customers involve wide range of industries, like mold & die, aerospace, electronic, machinery, etc. We are professional expert in cutting field. We would like to solve every problem from you. Please feel free to contact us, its our pleasure to serve for you. BW product including: cutting tool、aerospace tool .HSS DIN Cutting tool、Carbide end mills、Carbide cutting tool、NAS Cutting tool、NAS986 NAS965 NAS897 NAS937orNAS907 Cutting Tools,Carbide end mill、disc milling cutter,Aerospace cutting tool、Фрезеры’Carbide drill、High speed steel、Milling cutter、CVDD(Chemical Vapor Deposition Diamond )’PCBN (Polycrystalline Cubic Boron Nitride) ’Core drill、Tapered end mills、CVD Diamond Tools Inserts’PCD Edge-Beveling Cutter(Golden Finger’PCD V-Cutter’PCD Wood tools’PCD Cutting tools’PCD Circular Saw Blade’PVDD End Mills’diamond tool ‘Single Crystal Diamond ‘Metric end mills、Miniature end mills、Специальные режущие инструменты ‘Пустотелое сверло ‘Pilot reamer、Fraises’Fresas con mango’ PCD (Polycrystalline diamond) ‘Frese’Electronics cutter、Step drill、Metal cutting saw、Double margin drill、Gun barrel、Angle milling cutter、Carbide burrs、Carbide tipped cutter、Chamfering tool、IC card engraving cutter、Side cutter、NAS tool、DIN or JIS tool、Special tool、Metal slitting saws、Shell end mills、Side and face milling cutters、Side chip clearance saws、Long end mills、Stub roughing end mills、Dovetail milling cutters、Carbide slot drills、Carbide torus cutters、Angel carbide end mills、Carbide torus cutters、Carbide ball-nosed slot drills、Mould cutter、Tool manufacturer.
Bewise Inc. www.tool-tool.com
ようこそＢｅｗｉｓｅ Ｉｎｃ.の世界へお越し下さいませ、先ず御目出度たいのは新たな
情報を受け取って頂き、もっと各産業に競争力プラス展開。
弊社は専門なエンド・ミルの製造メーカーで、客先に色んな分野のニーズ、
豊富なパリエーションを満足させ、特にハイテク品質要求にサポート致します。
弊社は各領域に供給できる内容は：
（１）精密ＨＳＳエンド・ミルのＲ＆Ｄ
（２）Carbide Cutting tools設計
（３）鎢鋼エンド・ミル設計
（４）航空エンド・ミル設計
（５）超高硬度エンド・ミル
（６）ダイヤモンド・エンド・ミル
（７）医療用品エンド・ミル設計
（８）自動車部品＆材料加工向けエンド・ミル設計
弊社の製品の供給調達機能は：
（１）生活産業～ハイテク工業までのエンド・ミル設計
（２）ミクロ・エンド・ミル～大型エンド・ミル供給
（３）小Ｌｏｔ生産～大量発注対応供給
（４）オートメーション整備調達
（５）スポット対応～流れ生産対応
弊社の全般供給体制及び技術自慢の総合専門製造メーカーに貴方のご体験を御待ちしております。
BW специализируется в научных исследованиях и разработках, и снабжаем самым высокотехнологичным карбидовым материалом для поставки режущих / фрезеровочных инструментов для почвы, воздушного пространства и электронной индустрии. В нашу основную продукцию входит твердый карбид / быстрорежущая сталь, а также двигатели, микроэлектрические дрели, IC картонорезальные машины, фрезы для гравирования, режущие пилы, фрезеры-расширители, фрезеры-расширители с резцом, дрели, резаки форм для шлицевого вала / звездочки роликовой цепи, и специальные нано инструменты. Пожалуйста, посетите сайт www.tool-tool.com для получения большей информации.
留言列表
