Bewise Inc. www.tool-tool.com Reference source from the internet.
Schematic diagram of high-bypass turbofan engine
Boeing 747 jet engine up close
A turbofan is a type of jet engine, similar to a turbojet. It essentially consists of a ducted fan with a smaller diameter turbojet engine mounted behind it that powers the fan. Part of the airstream from the ducted fan passes through the turbojet where it is burnt to power the fan, but the majority of the flow bypasses it, and very often produces most of the thrust.[1]
A few designs work slightly differently and have the fan blades as a radial extension of an aft mounted low pressure turbine unit.
All of the jet-engines that power currently-manufactured commercial jet aircraft are turbofans. They are mainly used commercially because they are highly efficient and relatively quiet in operation.
Turbofans are also used in many military jet aircraft, but rarely in other vehicles (e.g. jet-powered cars) where very high speeds and lower weight are needed, while noise and efficiency are less important.
[edit] Introduction
In a turbojet, air enters an intake before being compressed to a higher pressure by a rotating (fan-like) compressor. The compressed air passes on to a combustor where it is mixed with a fuel (e.g. kerosene) and ignited. The hot combustion gases then enter a windmill-like turbine, where power is extracted to drive the compressor. Although the expansion process in the turbine reduces the gas pressure (and temperature), there is normally sufficient energy remaining to provide a high velocity jet, as the exhaust gases expand to atmospheric pressure through the propelling nozzle. This process normally produces a net thrust opposite in direction to that of the jet. Unlike a reciprocating engine, a turbojet undertakes a continuous flow process.
The description given above is, strictly speaking, for a single spool (shaft) turbojet. After World War II, 2-spool (shaft) turbojets were developed to make it easier to throttle-back compression systems with a high design overall pressure ratio (i.e. combustor inlet pressure/intake delivery pressure). Adopting the 2-spool arrangement enables the compression system to be split into two, with a Low Pressure (LP) Compressor supercharging a High Pressure (HP) Compressor. Each compressor is mounted on a separate (co-axial) shaft, driven by its own turbine (i.e HP Turbine and LP Turbine). Otherwise a 2-spool turbojet is much like a single spool engine.
Modern turbofans evolved from the 2-spool axial-flow turbojet engine, essentially by increasing the relative size of the Low Pressure (LP) Compressor to the point where some (if not most) of the air exiting the unit actually bypasses the core (or gas generator) stream, passing through the main combustor. This bypass air either expands through a separate propelling nozzle, or is mixed with the hot gases leaving the Low Pressure (LP) Turbine, before expanding through a Mixed Stream Propelling Nozzle. Owing to a lower jet velocity, a modern civil turbofan is quieter than the equivalent turbojet. Turbofans also have a better thermal efficiency, which is explained later in the article. In a turbofan, the LP Compressor is often called a fan. Civil turbofans usually have a single fan stage, whereas most military turbofans have multi-stage fans.
Turboprop engines are gas turbine engines that deliver almost all of their power to a shaft to drive a propeller. Turboprops remain popular on very small or slow aircraft such as small commuter airliners and combat transports such as the C-130 Hercules and P-3 Orion.
If the turboprop is better at moderate flight speeds and the turbojet is better at very high speeds, it might be imagined that at some speed range in the middle a mixture of the two is best. Such an engine is the turbofan (originally termed bypass turbojet by the inventors at Rolls Royce). Another name sometimes used is ducted fan, though that term is also used for propellers and fans used in vertical flight applications.
The difference between a turbofan and a propeller besides direct thrust, is that the intake duct of the former slows the air before it arrives at the fan face. As both propeller and fan blades must operate at subsonic inlet velocities to be efficient, ducted fans allow efficient operation at higher vehicle speeds.
duct work on an
A-7 Corsair — the decreasing diameter of the inlet duct slows incoming air.
Depending on specific thrust (i.e. net thrust/intake airflow), ducted fans operate best from about 400 to 2000 km/h (250 to 1300 mph), which is why turbofans are the most common type of engine for aviation use today in airliners, as well as subsonic/supersonic military fighter and trainer aircraft. It should be noted, however, that turbofans use extensive ducting to force incoming air to subsonic velocities (thus reducing shockwaves throughout the engine).
Bypass ratio (bypassed airflow to combustor airflow) is a parameter often used for classifying turbofans, although specific thrust is a better parameter.
The noise of any type of jet engine is strongly related to the velocity of the exhaust gases. High bypass ratio (i.e. low specific thrust) turbofans are relatively quiet compared to turbojets and low bypass ratio (i.e. high specific thrust) turbofans. A low specific thrust engine has a low jet velocity by definition, as the following approximate equation for net thrust implies:
where:
intake mass flow
fully expanded jet velocity (in the exhaust plume)
aircraft flight velocity
Rearranging the above equation, specific thrust is given by:
So for zero flight velocity, specific thrust is directly proportional to jet velocity. Relatively speaking, low specific thrust engines are large in diameter to accommodate the high airflow required for a given thrust.
Jet aircraft are often considered loud, but a conventional piston engine or a turboprop engine delivering the same power would be much louder.
[edit] Early turbofans
Early turbojet engines were very fuel-inefficient, as their overall pressure ratio and turbine inlet temperature were severely limited by the technology available at the time. The very first running turbofan was the Daimler-Benz DB 670 (aka 109-007) which was operated on its testbed on April 1, 1943. The engine was abandoned later while the war went on and problems could not be solved. Improved materials, and the introduction of twin compressors such as in the Pratt & Whitney JT3C engine, increased the overall pressure ratio and thus the thermodynamic efficiency of engines, but led to a poor propulsive efficiency, as pure turbojets have a high specific thrust/high velocity exhaust.
The original low-bypass turbofan engines were designed to improve propulsive efficiency by reducing the exhaust velocity to a value closer to that of the aircraft. The Rolls-Royce Conway, the first production turbofan, had a bypass ratio of 0.3, similar to the modern General Electric F404 fighter engine. Civilian turbofan engines of the 1960s, such as the Pratt & Whitney JT8D and the Rolls-Royce Spey had bypass ratios closer to 1, but were not disimilar to their military equivalents.
The unusual General Electric CF700 turbofan engine was developed as an aft-fan engine with a 2.0 bypass ratio. This was derived from the T-38 Talon and the Learjet General Electric J85/CJ610 turbojet (2,850 lbf or 12,650 N) to power the larger Rockwell Sabreliner 75/80 model aircraft, as well as the Dassault Falcon 20 with about a 50% increase in thrust (4,200 lbf or 18,700 N). The CF700 was the first small turbofan in the world to be certificated by the Federal Aviation Administration (FAA). There are now over 400 CF700 aircraft in operation around the world, with an experience base of over 10 million service hours. The CF700 turbofan engine was also used to train Moon-bound astronauts in Project Apollo as the powerplant for the Lunar Landing Research Vehicle.
[edit] Low bypass turbofans
Schematic diagram illustrating a 2-spool, low-bypass turbofan engine with a mixed exhaust, showing the low-pressure (green) and high-pressure (purple) spools. The fan (and booster stages) are driven by the low-pressure turbine, whereas the high-pressure compressor is powered by the high-pressure turbine
A high specific thrust/low bypass ratio turbofan normally has a multi-stage fan, developing a relatively high pressure ratio and, thus, yielding a high (mixed or cold) exhaust velocity. The core airflow needs to be large enough to give sufficient core power to drive the fan. A smaller core flow/higher bypass ratio cycle can be achieved by raising the (HP) turbine rotor inlet temperature.
Imagine a retrofit situation where a new low bypass ratio, mixed exhaust, turbofan is replacing an old turbojet, in a particular military application. Say the new engine is to have the same airflow and net thrust (i.e. same specific thrust) as the one it is replacing. A bypass flow can only be introduced if the turbine inlet temperature is allowed to increase, to compensate for a correspondingly smaller core flow. Improvements in turbine cooling/material technology would facilitate the use of a higher turbine inlet temperature, despite increases in cooling air temperature, resulting from a probable increase in overall pressure ratio.
Efficiently done, the resulting turbofan would probably operate at a higher nozzle pressure ratio than the turbojet, but with a lower exhaust temperature to retain net thrust. Since the temperature rise across the whole engine (intake to nozzle) would be lower, the (dry power) fuel flow would also be reduced, resulting in a better specific fuel consumption (SFC).
A few low-bypass ratio military turbofans (e.g. F404) have Variable Inlet Guide Vanes, with piano-style hinges, to direct air onto the first rotor stage. This improves the fan surge margin (see compressor map) in the mid-flow range. The swing wing F-111 achieved a very high range / payload capability by pioneering the use of this engine, and it was also the heart of the famous F-14 Tomcat air superiority fighter which used the same engines in a smaller, more agile airframe to achieve efficient cruise and Mach 2 speed.
[edit] Afterburning turbofans
Since the 1970s, most jet fighter engines have been low/medium bypass turbofans with a mixed exhaust, afterburner and variable area final nozzle – the first afterburning turbofan was the Pratt & Whitney TF30. An afterburner is a combustor located directly upstream of the nozzle. When lit, prodigious amounts of fuel are burnt in the afterburner, raising the temperature of exhaust gases by a significant amount, resulting in a higher exhaust velocity/engine specific thrust. The variable geometry nozzle must open to a larger throat area to accommodate the extra volume flow when the afterburner is lit. Afterburning gives a significant thrust boost for take off, transonic acceleration and combat maneuvers, but is very fuel intensive. Consequently afterburning can only be selected for relatively short proportions of a mission.
Unlike the main combustor, where the integrity of the downstream turbine blades must be preserved, an afterburner can operate at the ideal maximum (stoichiometric) temperature (i.e. about 2100K(3780R)). At a fixed total applied fuel:air ratio, the total fuel flow for a given fan airflow will be the same, regardless of the dry specific thrust of the engine. However, a high specific thrust turbofan will, by definition, have a higher nozzle pressure ratio, resulting in a higher afterburning net thrust and, therefore, a lower afterburning specific fuel consumption. However, high specific thrust engines have a high dry SFC. The situation is reversed for a medium specific thrust afterburning turbofan: i.e. poor afterburning SFC/good dry SFC. The former engine is suitable for a combat aircraft which must remain in afterburning combat for a fairly long period, but only has to fight fairly close to the airfield (i.e cross border skirmishes) The latter engine is better for an aircraft that has to fly some distance, or loiter for a long time, before going into combat. However, the pilot can only afford to stay in afterburning for a short period, before his/her fuel reserves become dangerously low.
Modern low-bypass military turbofans include the Pratt & Whitney F119, the Eurojet EJ200 and the General Electric F110 and F414, all of which feature a mixed exhaust, afterburner and variable area propelling nozzle. Non-afterburning engines include the Rolls-Royce/Turbomeca Adour (afterburning in the SEPECAT Jaguar) and the unmixed, vectored thrust, Rolls-Royce Pegasus.
[edit] High-bypass turbofan engines
Schematic diagram illustrating a 2-spool, high-bypass turbofan engine with an unmixed exhaust. The low-pressure spool is coloured green and the high-pressure one purple. Again, the fan (and booster stages) are driven by the low-pressure turbine, but more stages are required. A mixed exhaust is often employed nowadays
The low specific thrust/high bypass ratio turbofans used in today's civil jetliners (and some military transport aircraft) evolved from the high specific thrust/low bypass ratio turbofans used in such aircraft back in the 1960s.
Low specific thrust is achieved by replacing the multi-stage fan with a single stage unit. Unlike some military engines, modern civil turbofans do not have any stationary inlet guide vanes in front of the fan rotor. The fan is scaled to achieve the desired net thrust.
The core (or gas generator) of the engine must generate sufficient Core Power to at least drive the fan at its design flow and pressure ratio. Through improvements in turbine cooling/material technology, a higher (HP) turbine rotor inlet temperature can be used, thus facilitating a smaller (and lighter) core and (potentially) improving the core thermal efficiency. Reducing the core mass flow tends to increase the load on the LP turbine, so this unit may require additional stages to reduce the average stage loading and to maintain LP turbine efficiency. Reducing core flow also increases bypass ratio (5:1, or more, is now common).
Further improvements in core thermal efficiency can be achieved by raising the overall pressure ratio of the core. Improved blade aerodynamics reduces the number of extra compressor stages required. With multiple compressors (i.e. LPC, IPC, HPC) dramatic increases in overall pressure ratio have became possible. Variable geometry (i.e. stators) enable high pressure ratio compressors to work surge-free at all throttle settings.
Cutaway diagram of the General Electric CF6-6 engine
The first high-bypass turbofan engine was the General Electric TF39, built to power the Lockheed C-5 Galaxy military transport aircraft. The civil General Electric CF6 engine used a derived design. Other high-bypass turbofans are the Pratt & Whitney JT9D, the three-shaft Rolls-Royce RB211 and the CFM International CFM56. More recent large high-bypass turbofans include the Pratt & Whitney PW4000, the three-shaft Rolls-Royce Trent, the General Electric GE90/GEnx and the GP7000, produced jointly by GE and P&W.
High-bypass turbofan engines are generally quieter than the earlier low bypass ratio civil engines. This is not so much due to the higher bypass ratio, as to the use of a low pressure ratio, single stage, fan, which significantly reduces specific thrust and, thereby, jet velocity. The combination of a higher overall pressure ratio and turbine inlet temperature improves thermal efficiency. This, together with a lower specific thrust (better propulsive efficiency), leads to a lower specific fuel consumption.
For reasons of fuel economy, and also of reduced noise, almost all of today's jet airliners are powered by high-bypass turbofans. Although modern military aircraft tend to use low bypass ratio turbofans, military transport aircraft (e.g. C-17 ) mainly use high bypass ratio turbofans (or turboprops) for fuel efficiency.
Because of the implied low mean jet velocity, a high bypass ratio/low specific thrust turbofan has a high thrust lapse rate (with rising flight speed). Consequently the engine must be over-sized to give sufficient thrust during climb/cruise at high flight speeds (e.g. Mach 0.83). Because of the high thrust lapse rate, the static (i.e. Mach 0) thrust is consequently relatively high. This enables heavily laden, wide body, aircraft to accelerate quickly during take-off and consequently lift-off within a reasonable runway length.
The turbofans on twin engined airliners are further over-sized to cope with losing one engine during take-off, which reduces the thrust by 50%. Modern twin engined airliners normally climb very steeply immediately after take-off. If one engine is lost, the climb-out is much shallower, but sufficient to clear obstacles in the flightpath.
The Soviet Union's engine technology was less advanced than the West's and its first wide-body aircraft, the Ilyushin Il-86, was powered by low-bypass engines. The Yakovlev Yak-42, a medium-range, rear-engined aircraft seating up to 120 passengers was the first Soviet aircraft to use high-bypass engines.
[edit] Turbofan configurations
Turbofan engines come in a variety of engine configurations. For a given engine cycle (i.e. same airflow, bypass ratio, fan pressure ratio, overall pressure ratio and HP turbine rotor inlet temperature), the choice of turbofan configuration has little impact upon the design point performance (e.g. net thrust, SFC), as long as overall component performance is maintained. Off-design performance and stability is, however, affected by engine configuration.
As the design overall pressure ratio of an engine cycle increases, it becomes more difficult to throttle the compression system, without encountering an instability known as compressor surge. This occurs when some of the compressor aerofoils stall (like the wings of an aircraft) causing a violent change in the direction of the airflow. However, compressor stall can be avoided, at throttled conditions, by progressively:
1) opening interstage/intercompressor blow-off valves (inefficient)
and/or
2) closing variable stators within the compressor
Most modern American civil turbofans employ a relatively high pressure ratio High Pressure (HP) Compressor with several rows of variable stators to control surge margin. However, on the three-spool RB211/Trent the HP Compressor has a modest pressure ratio and can be throttled-back surge-free, without employing HP Compressor variable geometry.
[edit] Single shaft turbofan
Although far from common, the Single Shaft Turbofan is probably the simplest configuration, comprising a fan and high pressure compressor driven by a single turbine unit, all on the same shaft. The SNECMA M53, which powers Mirage fighter aircraft, is an example of a Single Shaft Turbofan. Despite the simplicity of the turbomachinery configuration, the M53 requires a variable area mixer to facilitate part-throttle operation.
[edit] Aft fan turbofan
One of the earliest turbofans was a derivative of the General Electric J79 turbojet, known as the CJ805, which featured an integrated aft fan/low pressure (LP) turbine unit located in the turbojet exhaust jetpipe. Hot gas from the turbojet turbine exhaust expanded through the LP turbine, the fan blades being a radial extension of the turbine blades. This Aft Fan configuration was later exploited in the General Electric GE-36 UDF (propfan) Demonstrator of the early 80's. One of the problems with the Aft Fan configuration is hot gas leakage from the LP turbine to the fan.
[edit] Basic two spool
Many turbofans have the Basic Two Spool configuration where both the fan and LP turbine (i.e. LP spool) are mounted on a second (LP) shaft, running concentrically with the HP spool (i.e. HP compressor driven by HP turbine). The Rolls-Royce BR710 is typical of this configuration. At the smaller thrust sizes, instead of all-axial blading, the HP compressor configuration may be axial-centrifugal (e.g. General Electric CFE738), double-centrifugal or even diagonal/centrifugal (e.g. Pratt & Whitney Canada PW600).
[edit] Boosted two spool
Higher overall pressure ratios can be achieved by either raising the HP compressor pressure ratio or adding an Intermediate Pressure (IP) Compressor between the fan and HP compressor, to supercharge or boost the latter unit helping to raise the overall pressure ratio of the engine cycle to the very high levels employed today (i.e. greater than 40:1, typically). All of the large American turbofans (e.g. General Electric CF6, GE90 and GEnx plus Pratt & Whitney JT9D and PW4000) feature an IP compressor mounted on the LP shaft and driven, like the fan, by the LP turbine, the mechanical speed of which is dictated by the tip speed and diameter of the fan. The high bypass ratios (i.e. fan duct flow/core flow) used in modern civil turbofans tends to reduce the relative diameter of the attached IP compressor, causing its mean tip speed to decrease. Consequently more IPC stages are required to develop the necessary IPC pressure rise.
[edit] Three spool
Rolls-Royce chose a Three Spool configuration for their large civil turbofans (i.e. the RB211 and Trent families), where the Intermediate Pressure IP compressor is mounted on a separate (IP) shaft, running concentrically with the LP and HP shafts, and is driven by a separate IP Turbine. Consequently, the IP compressor can rotate faster than the fan, increasing its mean tip speed, thereby reducing the number of IP stages required for a given IPC pressure rise. However, because the RB211/Trent designs have a higher IPC pressure rise than the American engines, the HPC pressure rise is less resulting in a shorter, lighter, more rigid engine. However, three spool engines are harder to both build and maintain. The greater rigidity means that there is less distortion of the engine casing under 'g' loads during flight, resulting in less blade tip rubbing and, therefore, a slower in-service deterioration of component performance and specific fuel consumption.
The Turbo-Union RB199 military turbofan also has a three spool configuration, and the Russian military Kuznetsov NK-321 has also.
[edit] Geared fan
As bypass ratio increases, the mean radius ratio of the fan and LP turbine increases. Consequently, if the fan is to rotate at its optimum blade speed the LP turbine blading will run slow, so additional LPT stages will be required, to extract sufficient energy to drive the fan. Introducing a reduction gearbox, with a suitable gear ratio, between the LP shaft and the fan, enables both the fan and LP turbine to operate at their optimum speeds. Typical of this configuration are the long established Honeywell TFE731 and the recent Pratt & Whitney Advanced Technology Fan Integrator (ATFI) demonstrator engine.
[edit] Cycle improvements
Consider a mixed turbofan with a fixed bypass ratio and airflow. Increasing the overall pressure ratio of the compression system raises the combustor entry temperature. Therefore, at a fixed fuel flow there is an increase in (HP) turbine rotor inlet temperature. Although the higher temperature rise across the compression system implies a larger temperature drop over the turbine system, the mixed nozzle temperature is unaffected, because the same amount of heat is being added to the system. There is, however, a rise in nozzle pressure, because overall pressure ratio increases faster than the turbine expansion ratio, causing an increase in the hot mixer entry pressure. Consequently, net thrust increases, whilst specific fuel consumption (fuel flow/net thrust) decreases. A similar trend occurs with unmixed turbofans.
So turbofans can be made more fuel efficient by raising overall pressure ratio and turbine rotor inlet temperature in unison. However, better turbine materials and/or improved vane/blade cooling are required to cope with increases in both turbine rotor inlet temperature and compressor delivery temperature. Increasing the latter may require better compressor materials.
[edit] Thrust growth
Thrust growth is obtained by increasing core power. There are two basic routes available:
a) hot route: increase HP turbine rotor inlet temperature
b) cold route: increase core mass flow
Both routes require an increase in the combustor fuel flow and, therefore, the heat energy added to the core stream.
The hot route may require changes in turbine blade/vane materials and/or better blade/vane cooling. The cold route can be obtained by one of the following:
- adding T-stages to the LP/IP compression
- adding a zero-stage to the HP compression
- improving the compression process, without adding stages (e.g. higher fan hub pressure ratio)
all of which increase both overall pressure ratio and core airflow.
Alternatively, the core size can be increased, to raise core airflow, without changing overall pressure ratio. This route is expensive, since a new (upflowed) turbine system (and possibly a larger IP compressor) is also required.
Changes must also be made to the fan to absorb the extra core power. On a civil engine, jet noise considerations mean that any significant increase in Take-off thrust must be accompanied by a corresponding increase in fan mass flow (to maintain a T/O specific thrust of about 30lbf/lb/s), usually by increasing fan diameter. On military engines, the fan pressure ratio would probably be increased to improve specific thrust, jet noise not normally being an important factor.
[edit] Technical Discussion
- Specific Thrust (net thrust/intake airflow) is an important parameter for turbofans and jet engines in general. Imagine a fan (driven by an appropriately sized electric motor) operating within a pipe, which is connected to a propelling nozzle. Fairly obviously, the higher the Fan Pressure Ratio (fan discharge pressure/fan inlet pressure), the higher the jet velocity and the corresponding specific thrust. Now imagine we replace this set-up with an equivalent turbofan - same airflow and same fan pressure ratio. Obviously, the core of the turbofan must produce sufficient power to drive the fan via the Low Pressure (LP) Turbine. If we choose a low (HP) Turbine Inlet Temperature for the gas generator, the core airflow needs to be relatively high to compensate. The corresponding bypass ratio is therefore relatively low. If we raise the Turbine Inlet Temperature, the core airflow can be smaller, thus increasing bypass ratio. Raising turbine inlet temperature tends to increase thermal efficiency and, therefore, improve fuel efficiency.
- Naturally, as altitude increases there is a decrease in air density and, therefore, the net thrust of an engine. There is also a flight speed effect, termed Thrust Lapse Rate. Consider the approximate equation for net thrust again:
With a high specific thrust (e.g. fighter) engine, the jet velocity is relatively high, so intuitively one can see that increases in flight velocity have less of an impact upon net thrust than a medium specific thrust (e.g. trainer) engine, where the jet velocity is lower. The impact of thrust lapse rate upon a low specific thrust (e.g. civil) engine is even more severe. At high flight speeds, high specific thrust engines can pick-up net thrust through the ram rise in the intake, but this effect tends to diminish at supersonic speeds because of shock wave losses.
- Thrust growth on civil turbofans is usually obtained by increasing fan airflow, thus preventing the jet noise becoming too high. However, the larger fan airflow requires more power from the core. This can be achieved by raising the Overall Pressure Ratio (combustor inlet pressure/intake delivery pressure) to induce more airflow into the core and by increasing turbine inlet temperature. Together, these parameters tend to increase core thermal efficiency and improve fuel efficiency.
- Some high bypass ratio civil turbofans use an extremely low area ratio (less than 1.01), convergent-divergent, nozzle on the bypass (or mixed exhaust) stream, to control the fan working line. The nozzle acts as if it has variable geometry. At low flight speeds the nozzle is unchoked (less than a Mach Number of unity), so the exhaust gas speeds up as it approaches the throat and then slows down slightly as it reaches the divergent section. Consequently, the nozzle exit area controls the fan match and, being larger than the throat, pulls the fan working line slightly away from surge. At higher flight speeds, the ram rise in the intake increases nozzle pressure ratio to the point where the throat becomes choked (M=1.0). Under these circumstances, the throat area dictates the fan match and, being smaller than the exit, pushes the fan working line slightly towards surge. This is not a problem, since fan surge margin is much better at high flight speeds.
- The off-design behaviour of turbofans is illustrated under compressor map and turbine map.
- Because modern civil turbofans operate at low specific thrust, they only require a single fan stage to develop the required fan pressure ratio. The desired overall pressure ratio for the engine cycle is usually achieved by multiple axial stages on the core compression. Rolls-Royce tend to split the core compression into two with an intermediate pressure (IP) supercharging the HP compressor, both units being driven by turbines with a single stage, mounted on separate shafts. Consequently, the HP compressor need only develop a modest pressure ratio (e.g.~4.5:1). US civil engines use much higher HP compressor pressure ratios (e.g. ~23:1 on the General Electric GE90) and tend to be driven by a two stage HP turbine. Even so, there are usually a few IP axial stages mounted on the LP shaft, behind the fan, to further supercharge the core compression system. Civil engines have multi-stage LP turbines, the number of stages being determined by the bypass ratio, the amount of IP compression on the LP shaft and the LP turbine blade speed.
- Because military engines usually have to be able to fly very fast at Sea Level, the limit on HP compressor delivery temperature is reached at a fairly modest design overall pressure ratio, compared with that of a civil engine. Also the fan pressure ratio is relatively high, to achieve a medium to high specific thrust. Consequently, modern military turbofans usually only have 5 or 6 HP compressor stages and only require a single stage HP turbine. Low bypass ratio military turbofans usually have one LP turbine stage, but higher bypass ratio engines need two stages. In theory, by adding IP compressor stages, a modern military turbofan HP compressor could be used in a civil turbofan derivative, but the core would tend to be too small for high thrust applications.
[edit] Recent developments in blade technology
The turbine blades in a turbofan engine are subject to high heat and stress, and require special fabrication. New material construction methods and material science have allowed blades, which were originally polycrystalline (regular metal), to be made from lined up metallic crystals and more recently mono-crystalline (i.e. single crystal) blades, which can operate at higher temperatures with less distortion.
Nickel-based superalloys are used for HP turbine blades in almost all of the modern jet engines. The temperature capabilities of turbine blades have increased mainly through four approaches: the manufacturing (casting) process, cooling path design, thermal barrier coating (TBC), and alloy development.
Although turbine blade (and vane) materials have improved over the years, much of the increase in (HP) turbine inlet temperatures is due to improvements in blade/vane cooling technology. Relatively cool air is bled from the compression system, bypassing the combustion process, and enters the hollow blade or vane. After picking up heat from the blade/vane, the cooling air is dumped into the main gas stream. If the local gas temperatures are low enough, downstream blades/vanes are uncooled and solid.
Strictly speaking, cycle-wise the HP Turbine Rotor Inlet Temperature (after the temperature drop across the HPT stator) is more important than the (HP) turbine inlet temperature. Although some modern military and civil engines have peak RITs of the order of 3300 °R (2840 °F) or 1833 K (1560 °C), such temperatures are only experienced for a short time (during take-off) on civil engines.
[edit] Turbofan engine manufacturers
The turbofan engine market is dominated by General Electric, Rolls-Royce plc and Pratt & Whitney, in order of market share. GE and SNECMA of France have a joint venture, CFM International which, as the 3rd largest manufacturer in terms of market share, fits between Rolls Royce and Pratt & Whitney. Rolls Royce and Pratt & Whitney also have a joint venture, International Aero Engines, specializing in engines for the Airbus A320 family, whilst finally, Pratt & Whitney and General Electric have a joint venture, Engine Alliance marketing a range of engines for aircraft such as the Airbus A380.
[edit] General Electric
GE Aircraft Engines, part of the General Electric Conglomerate, currently has the largest share of the turbofan engine market. Some of their engine models include the CF6 (available on the Boeing 767, Boeing 747, Airbus A330 and more), GE90 (only the Boeing 777) and GEnx (developed for the Airbus A350 & Boeing 787 currently in development) engines. On the military side, GE engines power many U.S. military aircraft, including the F110, powering 80% of the US Air Force's F-16 Vipers and the F404 and F414 engines, which power the Navy's F/A-18 Hornet and Super Hornet. Rolls Royce and General Electric are jointly developing the F136 engine to power the Joint Strike Fighter.
[edit] CFM International
CFM International is a joint venture between GE Aircraft Engines and SNECMA of France.
They have created the very successful CFM56 series, used on Boeing 737 and Airbus aircraft.
[edit] Rolls-Royce
Rolls-Royce plc is the second largest manufacturer of turbofans and is most noted for their RB211 and Trent series, as well as their joint venture engines for the Airbus A320 and Boeing MD-90 families (IAE V2500 with Pratt & Whitney and others), the Panavia Tornado (Turbo-Union RB199) and the Boeing 717 (BR700). Rolls Royce, as owners of the Allison Engine Company, have their engines powering the C-130 Hercules and several Embraer regional jets. Rolls-Royce Trent 970s were the first engines to power the new Airbus A380. It was also Rolls-Royce Olympus[2]/SNECMA jets that powered the now retired Concorde although they were turbojets rather than turbofans. The famous thrust vectoring Pegasus[2] engine is the primary powerplant of the Harrier "Jump Jet" and its derivatives.
[edit] Pratt & Whitney
Pratt & Whitney is third behind GE and Rolls-Royce in market share. The JT9D has the distinction of being chosen by Boeing to power the original Boeing 747 "Jumbo jet". The PW4000 series is the successor to the JT9D, and powers some Airbus A310, Airbus A300, Boeing 747, Boeing 767, Boeing 777, and MD-11 aircraft. The PW4000 is certified for 180-minute ETOPS when used in twinjets. The first family has a 94 inch fan diameter and is designed to power the Boeing 767, Boeing 747, MD-11, and the Airbus A300. The second family is the 100 inch (2.5 m) fan engine developed specifically for the Airbus A330 twinjet, and the third family has a diameter of 112 inch designed to power Boeing 777. The Pratt & Whitney F119 and its derivative, the F135, power the United States Air Force's F-22 Raptor and the international F-35 Lightning II, respectively. Rolls Royce are responsible for the lift fan which will provide the F-35B variants with a STOVL capability. The F100 engine was first used on the F-15 Eagle and F-16 Fighting Falcon. Newer Eagles and Falcons also come with GE F110 as an option, and the two are in competition.
[edit] Extreme bypass jet engines
In the 1970s Rolls-Royce/SNECMA tested a M45SD-02 turbofan fitted with variable pitch fan blades to improve handling at ultra low fan pressure ratios and to provide thrust reverse down to zero aircraft speed. The engine was aimed at ultra quiet STOL aircraft operating from city centre airports.
In a bid for increased efficiency with speed, a development of the turbofan and turboprop known as
