Bewise Inc. www.tool-tool.com Reference source from the internet.
A cylinder is the central working part of a reciprocating engine, the space in which a piston travels. Multiple cylinders are commonly arranged side by side in a bank, or engine block, which is typically cast from aluminum or iron before precision features are machined into it. The cylinders may then be lined with sleeves or liners of some harder metal, or given a wear-resistant coating such as Nikasil. Ceramic linings have also been tried, so far unsuccessfully, except with low-speed "oilless" steam engines.[1] A cylinder's displacement, or swept volume, is its cross-sectional area (the square of half the bore times pi ) times the distance the piston travels within the cylinder (the stroke). The engine displacement is the swept volume of one cylinder times the number of cylinders in the engine.
A piston is seated inside each cylinder by several metal piston rings which fit around its outside surface in machined grooves; typically two for compressional sealing and one to seal the oil (In steam engines only compressional sealing rings are used of which there can be from two to five on the piston; a fine vapour of oil is usually maintained suspended in the steam working in the cylinder. The rings make near contact with the hard walls of the liner, riding on a thin layer of lubricating oil which is essential to keep the engine from seizing up. This contact, and the resulting wear, explains the need for the hard lining on the inner surface of the cylinder. The breaking in or running in of an engine is a process whereby tiny irregularities in the metals are encouraged to form congruent grooves. An engine job or rebore is a process in which the cylinders are machined out to a slightly larger diameter, and new sleeves and piston rings installed.
[edit] Heat engines
- Main article: Heat engine
Heat engines, including Stirling engines, are sealed machines using pistons within cylinders to transfer energy from a heat source to a colder reservoir, often using steam or another gas as the working substance. (See Carnot cycle.) The first illustration depicts a longitudinal section of a cylinder in a steam engine. The sliding part at the bottom is the piston, and the upper sliding part is a distribution valve (in this case of the D slide valve type) that directs steam alternately into either end of the cylinder. Refrigerators and air conditioners are heat engines driven in reverse cycle as pumps.
[edit] Internal combustion engines
- Main article: Internal combustion engine
Internal combustion engines operate on the inherent volume change accompanying oxidation of gasoline (petrol), diesel fuel (or some other hydrocarbon) or ethanol, an expansion which is greatly enhanced by the heat produced. They are not classical heat engines since they expel the working substance, which is also the combustion product, into the surroundings.
The reciprocating motion of the pistons is translated into crankshaft rotation via connecting rods. As a piston moves back and forth, a connecting rod changes its angle; its distal end has a rotating link to the crankshaft. In addition to cylinder-piston engines, there are also rotary turbines. The Wankel engine is a rotary adaptation of the cylinder-piston concept which has been used by Mazda in automobiles. Rotary engines are relatively quiet because they lack the clatter of reciprocating motion.
Air-cooled engines generally use individual cases for the cylinders to facilitate cooling. Inline motorcycle engines are an exception, having two-, three-, four-, or even six-cylinder air-cooled units in a common block. Water-cooled engines with only a few cylinders may also use individual cylinder cases, though this makes the cooling system more complex. The Ducati motorcycle company, which for years used air-cooled motors with individual cylinder cases, retained the basic design of their V-twin engine while adapting it to water-cooling.
In some engines, especially French designs, the cylinders have "wet liners". They are formed separately from the main casting so that liquid coolant is free to flow around their outsides. Wet-lined cylinders have better cooling and a more even temperature distribution, but this design makes the engine as a whole somewhat less rigid.
A typical four-cylinder automobile engine has a single row of water-cooled cylinders. V engines (V6 or V8) use two angled cylinder banks. The "V" is designed to minimize vibration through destructive interference of harmonic overtones. (The "straight-eight" engine is a thing of the past.) Many other engine configurations exist.
During use, the cylinder is subject to wear from the rubbing action of the piston rings and piston skirt. This is minimized by the thin oil film which coats the cylinder walls, but eventually the cylinder becomes worn and slightly oval in shape, usually necessitating a rebore to an oversize diameter and the fitting of new, oversize pistons. The cylinder does not wear above the highest point reached by the top compression ring of the piston, which can result in a detectable ridge. If an engine is only operated at low rpm for its early life (e.g. in a gently driven automobile) then abruptly used in the higher rpm range (e.g. by a new owner), the slight stretching of the connecting rods at high speed can enable the top compression ring to contact the wear ridge, breaking the ring. For this reason it is important that all engines, once initially run-in, are occasionally "exercised" through their full speed range to develop a tapered wear profile rather than a sharp ridge.
歡迎來到Bewise Inc.的世界，首先恭喜您來到這接受新的資訊讓產業更有競爭力，我們是提供專業刀具製造商，應對客戶高品質的刀具需求，我們可以協助客戶滿足您對產業的不同要求，我們有能力達到非常卓越的客戶需求品質，這是現有相關技術無法比擬的，我們成功的滿足了各行各業的要求，包括：精密HSS DIN切削刀具、協助客戶設計刀具流程、DIN or JIS 鎢鋼切削刀具設計、NAS986 NAS965 NAS897 NAS937orNAS907 航太切削刀具,NAS航 太刀具設計、超高硬度的切削刀具、醫療配件刀具設計、汽車業刀具設計、電子產業鑽石刀具、木工產業鑽石刀具等等。我們的產品涵蓋了從民生刀具到工業級的刀 具設計；從微細刀具到大型刀具；從小型生產到大型量產；全自動整合；我們的技術可提供您連續生產的效能，我們整體的服務及卓越的技術，恭迎您親自體驗！！
BW Bewise Inc. Willy Chen willy@tool-tool.com bw@tool-tool.com www.tool-tool.com skype:willy_chen_bw mobile:0937-618-190 Head &Administration Office No.13,Shiang Shang 2nd St., West Chiu Taichung,Taiwan 40356 TEL:+886 4 24710048 / FAX:+886 4 2471 4839 N.Branch
Welcome to BW tool world! We are an experienced tool maker specialized in cutting tools. We focus on what you need and endeavor to research the best cutter to satisfy users’ demand. Our customers involve wide range of industries, like mold & die, aerospace, electronic, machinery, etc. We are professional expert in cutting field. We would like to solve every problem from you. Please feel free to contact us, its our pleasure to serve for you. BW product including: cutting tool、aerospace tool .HSS DIN Cutting tool、Carbide end mills、Carbide cutting tool、NAS Cutting tool、NAS986 NAS965 NAS897 NAS937orNAS907 Cutting Tools,Carbide end mill、disc milling cutter,Aerospace cutting tool、Фрезеры’Carbide drill、High speed steel、Milling cutter、CVDD(Chemical Vapor Deposition Diamond )’PCBN (Polycrystalline Cubic Boron Nitride) ’Core drill、Tapered end mills、CVD Diamond Tools Inserts’PCD Edge-Beveling Cutter(Golden Finger’PCD V-Cutter’PCD Wood tools’PCD Cutting tools’PCD Circular Saw Blade’PVDD End Mills’diamond tool ‘Single Crystal Diamond ‘Metric end mills、Miniature end mills、Специальные режущие инструменты ‘Пустотелое сверло ‘Pilot reamer、Fraises’Fresas con mango’ PCD (Polycrystalline diamond) ‘Frese’Electronics cutter、Step drill、Metal cutting saw、Double margin drill、Gun barrel、Angle milling cutter、Carbide burrs、Carbide tipped cutter、Chamfering tool、IC card engraving cutter、Side cutter、NAS tool、DIN or JIS tool、Special tool、Metal slitting saws、Shell end mills、Side and face milling cutters、Side chip clearance saws、Long end mills、Stub roughing end mills、Dovetail milling cutters、Carbide slot drills、Carbide torus cutters、Angel carbide end mills、Carbide torus cutters、Carbide ball-nosed slot drills、Mould cutter、Tool manufacturer.
Bewise Inc. www.tool-tool.com
ようこそＢｅｗｉｓｅ Ｉｎｃ.の世界へお越し下さいませ、先ず御目出度たいのは新たな
情報を受け取って頂き、もっと各産業に競争力プラス展開。
弊社は専門なエンド・ミルの製造メーカーで、客先に色んな分野のニーズ、
豊富なパリエーションを満足させ、特にハイテク品質要求にサポート致します。
弊社は各領域に供給できる内容は：
（１）精密ＨＳＳエンド・ミルのＲ＆Ｄ
（２）Carbide Cutting tools設計
（３）鎢鋼エンド・ミル設計
（４）航空エンド・ミル設計
（５）超高硬度エンド・ミル
（６）ダイヤモンド・エンド・ミル
（７）医療用品エンド・ミル設計
（８）自動車部品＆材料加工向けエンド・ミル設計
弊社の製品の供給調達機能は：
（１）生活産業～ハイテク工業までのエンド・ミル設計
（２）ミクロ・エンド・ミル～大型エンド・ミル供給
（３）小Ｌｏｔ生産～大量発注対応供給
（４）オートメーション整備調達
（５）スポット対応～流れ生産対応
弊社の全般供給体制及び技術自慢の総合専門製造メーカーに貴方のご体験を御待ちしております。
BW специализируется в научных исследованиях и разработках, и снабжаем самым высокотехнологичным карбидовым материалом для поставки режущих / фрезеровочных инструментов для почвы, воздушного пространства и электронной индустрии. В нашу основную продукцию входит твердый карбид / быстрорежущая сталь, а также двигатели, микроэлектрические дрели, IC картонорезальные машины, фрезы для гравирования, режущие пилы, фрезеры-расширители, фрезеры-расширители с резцом, дрели, резаки форм для шлицевого вала / звездочки роликовой цепи, и специальные нано инструменты. Пожалуйста, посетите сайт www.tool-tool.com для получения большей информации.
留言列表
