Bewise Inc. www.tool-tool.com Reference source from the internet.
| Transmission types |
|---|
| Manual |
| Continuously variable |
| Bicycle gearing |
A continuously variable transmission (CVT) is a transmission which can change steplessly through an infinite number of effective gear ratios between maximum and minimum values. This contrasts with other mechanical transmissions that only allow a few different discrete gear ratios to be selected. The flexibility of a CVT allows the driving shaft to maintain a constant angular velocity over a range of output velocities. This can provide better fuel economy than other transmissions by enabling the engine to run at its most efficient revolutions per minute (RPM) for a range of vehicle speeds.
[edit] Uses
Many small tractors for home and garden use have simple hydrostatic or rubber belt CVTs. For example, the John Deere Gator line of small utility vehicles use a belt with a conical pulley system. They can deliver a lot of power and can reach speeds of 10-15 MPH, all without need for a clutch or shift gears. Many new snowmobiles and motorscooters use CVTs. Virtually all snowmobile and motor scooter CVTs are rubber belt/variable pulley CVTs.
Some combine harvesters have CVTs. The CVT allows the forward speed of the combine to be adjusted independently of the engine speed. This allows the operator to slow down and speed up as needed to accommodate variations in thickness of the crop.
CVTs have been used in aircraft electrical power generating systems since the 1950s and in SCCA Formula 500 race cars since the early 1970s. More recently, CVT systems have been developed for go-karts and have proven to increase performance and engine life expectancy. The Tomcar range of off-road vehicles also utilizes the CVT system.
Some older drill presses contain a pulley-based CVT where the output shaft has a pair of manually-adjustable conical pulley halves which a wide drive belt from the motor loops through. The pulley on the motor, however, is usually fixed in diameter, or may have a series of given-diameter steps to allow a selection of speed ranges. A handwheel on the drill press, marked with a scale corresponding to the desired machine speed, is mounted to a reduction gearing system for the operator to precisely control the width of the gap between the pulley halves. This gap width thus adjusts the gearing ratio between the motor's fixed pulley and the output shaft's variable pulley, changing speed of the chuck; a tensioner pulley is implemented in the belt transmission to take up or release the slack in the belt as the speed is altered. In most cases, however, the drill press' speed cannot be changed without the motor running.
[edit] Advantages and Disadvantages
[edit] Advantages
- CVTs can compensate for changing vehicle speeds, allowing the engine speed to remain at its level of peak efficiency. This improves fuel economy and by effect, exhaust emissions.
- CVTs operate smoothly since there are no gear changes which cause sudden jerks.
[edit] Disadvantages
- Many early CVT driven cars had disappointing performance. The original Ford Fiesta 1.1 CTX, for example, used 8.2 percent more gasoline than the manual transmission version in city driving.[1]
- CVTs operate smoothly. This can give a perception of low power, because many drivers expect a jerk when they begin to move the vehicle. The expected jerk of a non-CVT can be emulated by CVT control software though, eliminating this marketing problem.
- Since the CVT keeps the engine turning at constant RPM over a wide range of vehicle speeds, pressing on the accelerator pedal will make the car move faster but doesn't change the sound coming from the engine as much as a conventional automatic transmission gear-shift. This confuses some drivers and, again, leads to an impression of a lack of power.
- CVT torque handling capability is limited by the strength of their transmission medium (usually a belt or chain), and by their ability to withstand friction wear between torque source and transmission medium for friction-driven CVTs. CVTs in production prior to 2005 are predominantly belt or chain driven and therefore typically limited to low powered cars and other light duty applications. Units using advanced lubricants, however, have been proven to support any amount of torque in production vehicles, including that used for buses, heavy trucks, and earth moving equipment.
- Because automotive CVTs are automatic, they are stigmatized in regions such as southern Europe which do not generally accept automatic transmissions of any kind. Japan with its generally smaller cars and stop-and-go traffic, has proven a much better market for CVT driven cars.[1]
[edit] Types
[edit] Variable-diameter pulley (VDP) or Reeves drive
In this most common CVT system, [2] there are two V-belt pulleys that are split perpendicular to their axes of rotation, with a V-belt running between them. The gear ratio is changed by moving the two sections of one pulley closer together and the two sections of the other pulley farther apart. Due to the V-shaped cross section of the belt, this causes the belt to ride higher on one pulley and lower on the other. Doing this changes the effective diameters of the pulleys, which changes the overall gear ratio. The distance between the pulleys does not change, and neither does the length of the belt, so changing the gear ratio means both pulleys must be adjusted (one bigger, the other smaller) simultaneously to maintain the proper amount of tension on the belt.
Diagrams:
[edit] Toroidal or roller-based CVT
Toroidal CVTs are made up of discs and rollers that transmit power between the discs. The discs can be pictured as two almost conical parts, point to point, with the sides dished such that the two parts could fill the central hole of a torus. One disc is the input, and the other is the output (they do not quite touch). Power is transferred from one side to the other by rollers. When the roller's axis is perpendicular to the axis of the near-conical parts, it contacts the near-conical parts at same-diameter locations and thus gives a 1:1 gear ratio. The roller can be moved along the axis of the near-conical parts, changing angle as needed to maintain contact. This will cause the roller to contact the near-conical parts at varying and distinct diameters, giving a gear ratio of something other than 1:1. Systems may be partial or full toroidal. Full toroidal systems are the most efficient design while partial toroidals may still require a torque converter, and hence lose efficiency.
Diagrams:
[edit] Infinitely Variable Transmission (IVT)
A specific type of CVT is the infinitely variable transmission (IVT), in which the range of ratios of output shaft speed to input shaft speed includes a zero ratio that can be continuously approached from a defined "higher" ratio. A zero output speed with a finite input speed implies an infinite input-to-output speed ratio, which can be continuously approached from a given finite input value with an IVT. Low gears are a reference to low ratios of output speed to input speed. This ratio is taken to the extreme with IVTs, resulting in a "neutral", or non-driving "low" gear limit, in which the output speed is zero, although, unlike neutral in a normal automotive transmission, the output torque may be non-zero: the output shaft is rigidly fixed at zero speed rather than being freely rotating.
Most IVTs result from the combination of a CVT with an epicyclic gear system (which is also known as a planetary gear system) which enforces an output shaft rotation speed which is equal to the difference between two other speeds. If these two other speeds are the input and output of a CVT, there can be a setting of the CVT that results in an output speed of zero. The maximum output/input ratio can be chosen from infinite practical possibilities through selection of additional input or output gear, pulley or sprocket sizes without affecting the zero output or the continuity of the whole system. The IVT is always engaged, even during its zero output adjustment.
IVTs can in some implementations offer better efficiency when compared to other CVTs as in the preferred range of operation because most of the power flows through the planetary gear system and not the controlling CVT. Torque transmission capability can also be increased. There's also possibility to stage power splits for further increase in efficiency, torque transmission capability and better maintenance of efficiency of a wide gear ratio range.
An example of a true IVT is the Hydristor because the front unit connected to the engine can displace from zero to 27 cubic inches per revolution forward and zero to -10 cubic inches per revolution reverse. The rear unit is capable of zero to 75 cubic inches per revolution.
[edit] Ratcheting CVT
The ratcheting CVT is a Transmission that relies on static friction and is based on a set of elements that successively become engaged and then disengaged between the driving system and the driven system, often using oscillating or indexing motion in conjunction with one-way clutches or ratchets that rectify and sum only "forward" motion. The transmission ratio is adjusted by changing linkage geometry within the oscillating elements, so that the summed maximum linkage speed is adjusted, even when the average linkage speed remains constant. Power is transferred from input to output only when the clutch or ratchet is engaged, and therefore when it is locked into a static friction mode where the driving & driven rotating surfaces momentarily rotate together without slippage.
These CVTs can transfer substantial torque because their static friction actually increases relative to torque throughput, so slippage is impossible in properly designed systems. Efficiency is generally high because most of the dynamic friction is caused by very slight transitional clutch speed changes. The drawback to ratcheting CVTs is vibration caused by the successive transition in speed required to accelerate the element which must supplant the previously operating & decelerating, power transmitting element.
Ratcheting CVTs are distinguished from VDPs and roller-based CVTs by being static friction-based devices, as opposed to being dynamic friction-based devices that waste significant energy through slippage of twisting surfaces. An example of a racheting CVT one prototyped as a bicycle transmission protected under U.S. Patent #5516132 in which strong pedalling torque causes this mechanism to react against the spring, moving the ring gear/chainwheel assembly toward a concentric, lower gear position. When the pedalling torque relaxes to lower levels, the transmission self-adjusts toward higher gears, accompanied by an increase in transmission vibration.
A running prototype and functioning animation of a two stage ratcheting CVT can be found below:
[edit] Hydrostatic CVTs
Hydrostatic transmissions use a variable displacement pump and a hydraulic motor. All power is transmitted by hydraulic fluid. These types can generally transmit more torque, but can be sensitive to contamination. Some designs are also very expensive. However, they have the advantage that the hydraulic motor can be mounted directly to the wheel hub, allowing a more flexible suspension system and eliminating efficiency losses from friction in the drive shaft and differential components. This type of transmission is relatively easy to use because all forward and reverse speeds can be accessed using a single lever.
This type of transmission has been effectively applied to a variety of inexpensive and expensive versions of ridden lawn mowers and garden tractors. Many versions of riding lawn mowers and garden tractors propelled by a hydrostatic transmission are capable of pulling a reverse tine tiller and even a single bladed plow. The largest producers of such transmission are Hydro-Gear®, located in Sullivan, Illinois, and Tuff Torq®, a wholly-owned subsidiary of Kanzaki® (aka Kanzaki Kokyukoki), which is a subsidiary of Yanmar.
One class of riding lawn mower that has recently gained in popularity with consumers is zero turning radius mowers. These mowers have traditionally been powered with wheel hub mounted hydraulic motors driven by continuously variable pumps, but this design is relatively expensive. Hydro-Gear®, a joint venture between Sauer-Danfoss and Agri-Fab, Inc., of Sullivan, Illinois, created the first cost-effective integrated hydrostatic transaxle suitable for propelling consumer zero turning radius mowers. An integrated hydrostatic transaxle (IHT) uses a single housing for both hydraulic elements and gear-reducing elements.
Some heavy equipment may also be propelled by a hydrostatic transmission; e.g. agricultural machinery including foragers combines and some tractors. A variety of heavy earth-moving equipment manufactured by Caterpillar Inc., e.g. compact and small wheel loaders, track type loaders and tractors, skid-steered loaders and asphalt compactors use hydrostatic transmission. Hydrostatic CVTs are usually not used for extended duration high torque applications due to the heat that is generated by the flowing oil.
[edit] Variable toothed wheel transmission
A variable toothed wheel transmission is not a true CVT that can alter its ratio in infinite increments but rather approaches CVT capability by having a large number of ratios, typically 49. This transmission relies on a toothed wheel positively engaged with a chain where the toothed wheel has the ability to add or subtract a tooth at a time in order to alter its ratio with relation to the chain it is driving. The "toothed wheel" can take on many configurations including ladder chains, drive bars and sprocket teeth. The huge advantage of this type of CVT is that it is a positive mechanical drive and thus does not have the frictional losses and limitations of the Roller based or VDP CVT’s. The challenge in this type of CVT is to add or subtract a tooth from the toothed wheel in a very precise and controlled way in order to maintain synchronized engagement with the chain. This type of transmission has the potential to change ratios under load because of the large number of ratios resulting in the order of 3% ratio change differences between ratios, thus a clutch or torque converter is only necessary for pull away. No CVTs of this type are in commercial use probably because of above mentioned development challenge.
Diagram and video clip:
[edit] Cone CVTs
 |
This article is a rough translation of an article in another language. It may have been generated by a computer or by a translator with limited proficiency in English or the original language. Feel free to enhance the translation. For reference, the original article may appear under "{{{1}}}" in the "languages" list. |
Belong to this category all the CVTs that are constituted by one or more conical bodies that cooperate along their respective generatrices, thus realizing the variation.
In the one cone type there is a revolving body (a wheel) that, moving on the generatrix of the cone, creates the variation between the inferior and the superior diameter of the cone.
In the CVTs constituted by two or more cones (see GIF website), these are placed in opposition (with the inferior diameter of one cone facing the superior diameter of the other cone) and the contact between all the possible diameters of the two cones is realized by a ring interposed between the cones. The variation is realized by moving the ring along the generatrix of the two cones.
In a CVT with oscillating cones, the torque is transmitted via friction from a variable number of cones ( according to the torque to be transmitted )to a central barrel-shaped hub. The side surface of the hub is convexe according to a determinate radius of curvature, which is smaller than the concavity radius of the cones. In this way, there will be only one ( theoretical ) contact point between the cone and the hub.
A new revolutionary CVT using this technology was presented in Berlin during the 6th International CTI Symposium of Innovative Automotive Transmission, on 3-7 December 2007. Its name is Warko.
A particular characteristic of Warko is the absence of clutch: the engine is always connected to the wheels and the rear drive is realized by means of an epicyclic system in output. This system, named “power split”, allows the condition of geared neutral or "zero Dynamic": when the engine turns( connected to the sun gear of the epicyclic system), the variator ( which rotates the ring of the epicyclic system in the opposite sense to the sun gear), in a particular position of its range, will compensate for the engine rotation, having zero turns in output ( planetary = the output of the system ). As a consequence, the satellite gears roll within an internal ring gear.
Modularity, wide ratio range (= 9), high efficiency (95%), high torque capability (up to 500 Nm) and compactness (less than 36 cm length for 31 cm diameter and 60 kg) are the most important characteristics of Warko.
The same device, with the same identical cone, in different assembly levels, covers the 90% of the engines produced all over the world, with a power range that goes from 60 to 200 Hp gasoline and diesel. As a consequence, being manufactured in millions of pieces, its production costs will be comparable to mechanical transmission costs.
Diagrams:
[edit] History
Leonardo da Vinci, in 1490, conceptualized a stepless continuously variable transmission. [3] The first patent for a toroidal CVT was filed in in Europe in 1886, and a US Patent for one was granted in 1935. [4]
A CVT, called Variomatic, was designed and built by Huub van Doorne, co-founder of Van Doorne's Automobiel Fabriek (DAF), in the late 1950s, specifically to produce an automatic transmission for a small, affordable car. The first DAF car using van Doorne's CVT, the DAF 600,was produced in 1958. [5] Van Doorne's patents were later transferred to a company called VDT (Van Doorne Transmissie B.V.) when the passenger car division was sold to Volvo; its CVT was used in Volvo 340.
In early 1987, Subaru launched the Justy in Tokyo with an electronically controlled continuously variable transmission (ECVT) developed by Fuji Heavy Industries, which owns Subaru. In 1989 the Justy became the first production car in the U.S. to offer CVT technology. While the Justy saw only limited success, Subaru continues to use CVT in its keicars to this day, while also supplying it to other manufacturers.[1]
In the summer of 1987 the Ford Fiesta and Fiat Uno became the first mainstream European cars to be equipped with steel-belted CVT (as opposed to the less robust rubber-belted DAF design). This CVT, the Ford CTX was developed by Ford, Van Doorne, and Fiat, with work on the transmission starting in 1976.[1]
The 1992 Nissan March contained Nissan's N-CVT based on the Fuji Heavy Industries ECVT.[1] In the late 1990s, Nissan designed its own CVT that allowed for higher torque, and includes a torque converter. This gearbox was used in a number of Japanese market models. Nissan is also the only car maker to bring roller-based CVT to the market in recent years. Their toroidal CVT, named the Extroid, was available in the Japanese market Y34 Nissan Gloria and V35 Skyline GT-8. However, the gearbox was not carried over when the Cedric/Gloria was replaced by the Nissan Fuga in 2004.
After studying pulley-based CVT for years, Honda also introduced their own version on the 1995 Honda Civic VTi. Dubbed Honda Multi Matic, this CVT gearbox accepted higher torque than traditional pulley CVTs, and also includes a torque converter for "creep" action. The CVT is also currently employed in the Honda City ZX that is manufactured in India.
Toyota used an Power Split Transmission (PST) in the 1997 Prius, and all subsequent Toyota and Lexus hybrids sold internationally continue to use the system (marketed under the Hybrid Synergy Drive name). Although sold as a ECVT it is in fact not such a device as the gear ratios are fixed. The PST allows either the electric motor or the internal combustion engine (ICE) or both to propel the vehicle. The response of the complete system (under computer control) is similar in feel to a CVT in that the ICE speed is relatively low and constant under low power or high and constant under high power.
Audi has, since 2000, offered a chain-type CVT as an option on some of its larger-engine models, for example the A4 3.0 L V6.
BMW used a belt-drive CVT as an option for the low and middle range MINI in 2001, forsaking it only on the supercharged version of the car where the increased torque levels demanded a conventional automatic gearbox. The CVT could also be manually "shifted" if desired with software simulated shift points.
Ford introduced a chain-driven CVT known as the CFT30 in their 2005 Ford Freestyle, Ford Five Hundred and Mercury Montego. The transmission was designed in cooperation with German automotive supplier ZF Friedrichshafen and was produced in Batavia, Ohio at Batavia Transmissions LLC (a subsidiary of Ford Motor Company) until March 22, 2007. The Batavia plant also produced the belt-driven CFT23 CVT which went in the Ford Focus C-MAX. Ford also sold Escort and Orion models in Europe with CVTs in the 1980s and 1990s.
Contract agreements were established in 2006 between MTD Products and Torotrak for the first full toroidal system to be manufactured for outdoor power equipment such as jet skis, ski-mobiles and ride-on mowers.[6]
The 2007 Dodge Caliber and the related Jeep Compass employ a CVT using a variable pulley system as their optional automatic transmission.[7]
The 2008 Mitsubishi Lancer model is available with CVT transmission as the automatic transmission. DE and ES models receive a standard CVT with Drive and Low gears; the GTS model is equipped with a standard Drive and also a Sportronic mode that allows the driver to use 6 different preset gear ratios (either with the shifter or steering wheel-mounted paddle shifters).
歡迎來到Bewise Inc.的世界，首先恭喜您來到這接受新的資訊讓產業更有競爭力，我們是提供專業刀具製造商，應對客戶高品質的刀具需求，我們可以協助客戶滿足您對產業的不同要求，我們有能力達到非常卓越的客戶需求品質，這是現有相關技術無法比擬的，我們成功的滿足了各行各業的要求，包括：精密HSS DIN切削刀具、協助客戶設計刀具流程、DIN or JIS 鎢鋼切削刀具設計、NAS986 NAS965 NAS897 NAS937orNAS907 航太切削刀具,NAS航太刀具設計、超高硬度的切削刀具、醫療配件刀具設計、汽車業刀具設計、電子產業鑽石刀具、木工產業鑽石刀具等等。我們的產品涵蓋了從民生刀具到工業級的刀具設計；從微細刀具到大型刀具；從小型生產到大型量產；全自動整合；我們的技術可提供您連續生產的效能，我們整體的服務及卓越的技術，恭迎您親自體驗！！
BW Bewise Inc. Willy Chen willy@tool-tool.com bw@tool-tool.com www.tool-tool.com skype:willy_chen_bw mobile:0937-618-190 Head &Administration Office No.13,Shiang Shang 2nd St., West Chiu Taichung,Taiwan 40356 http://www.tool-tool..com / FAX:+886 4 2471 4839 N.Branch 5F,No.460,Fu Shin North Rd.,Taipei,Taiwan S.Branch No.24,Sec.1,Chia Pu East Rd.,Taipao City,Chiayi Hsien,Taiwan
Welcome to BW tool world! We are an experienced tool maker specialized in cutting tools. We focus on what you need and endeavor to research the best cutter to satisfy users’ demand. Our customers involve wide range of industries, like mold & die, aerospace, electronic, machinery, etc. We are professional expert in cutting field. We would like to solve every problem from you. Please feel free to contact us, its our pleasure to serve for you. BW product including: cutting tool、aerospace tool .HSS DIN Cutting tool、Carbide end mills、Carbide cutting tool、NAS Cutting tool、NAS986 NAS965 NAS897 NAS937orNAS907 Cutting Tools,Carbide end mill、disc milling cutter,Aerospace cutting tool、hss drill’Фрезеры’Carbide drill、High speed steel、Milling cutter、CVDD(Chemical Vapor Deposition Diamond )’PCBN (Polycrystalline Cubic Boron Nitride) ’Core drill、Tapered end mills、CVD Diamond Tools Inserts’PCD Edge-Beveling Cutter(Golden Finger’PCD V-Cutter’PCD Wood tools’PCD Cutting tools’PCD Circular Saw Blade’PVDD End Mills’diamond tool ‘Single Crystal Diamond ‘Metric end mills、Miniature end mills、Специальные режущие инструменты ‘Пустотелое сверло ‘Pilot reamer、Fraises’Fresas con mango’ PCD (Polycrystalline diamond) ‘Frese’Electronics cutter、Step drill、Metal cutting saw、Double margin drill、Gun barrel、Angle milling cutter、Carbide burrs、Carbide tipped cutter、Chamfering tool、IC card engraving cutter、Side cutter、NAS tool、DIN or JIS tool、Special tool、Metal slitting saws、Shell end mills、Side and face milling cutters、Side chip clearance saws、Long end mills、Stub r
